how to test a furnace blower motor with a multimeter

| |

If you’re like most people, you probably don’t know how to test a furnace blower motor with a multimeter. But don’t worry, we’re here to help! In this blog post, we’ll show you how to do it quickly and easily. Trust us, it’s not as complicated as it sounds!

how to test a furnace blower motor with a multimeter

A multimeter is a useful tool that allows you to test for Continuity, or the flow of electricity through a given material. You can use your multimeter to test whether or not your furnace blower motor is functioning properly.

To do so, first make sure that your multimeter is turned off. Then, remove the wires from the furnace blower motor. Next, attach the red lead from your multimeter to one of the exposed ends of wire on the furnace blower motor. Then, touch the black lead from your multimeter to the other exposed end of wire on the furnace blower motor.

Once you have done this, turn on your multimeter. If the reading on your multimeter is “0,” then this indicates that there is no Continuity present, and therefore, your furnace blower motor is not working properly.

how to test a furnace blower motor

To test a furnace blower motor, first disconnect the power to the furnace. Next, remove the blower motor from the furnace and test it with a multimeter. If the blower motor is working properly, it should read between 0.5 and 1.0 ohms.

how to test a furnace

A furnace blower motor is an important part of a furnace. The blower motor pushes air through the furnace filter and into the home. If the blower motor is not working, the furnace will not be able to push air through the filter and into the home, and the home will not be heated.

There are two ways to test a furnace blower motor: with a multimeter or with a continuity tester.

With a multimeter:
1.Turn off the power to the furnace.
2.Remove the access panel to the blower motor.
3.Locate the two wires that go to the blower motor.
4.Set your multimeter to ohms/resistance mode.
5.Place one lead of your multimeter on each of the wires going to the blower motor.
6.If your multimeter reads infinity (∞), then the windings in the blower motor are open and you will need to replace the blower motor. If your multimeter reads 0 ohms, then the windings are shorted and you will also need to replace the blower motor

how to test a blower motor

Before you begin testing the motor, make sure that it is clean and free of debris. To test the motor, you will need a multimeter.

Turn off the power to the furnace at the breaker box.
Remove the access panel to the blower compartment.
Locate the blower motor. It will be mounted on a bracket inside the compartment.
Using the multimeter, set it to the AC voltage setting.
Touch one probe of the meter to each of the black wires connected to the motor terminals. If there is no voltage reading, flip the breaker switch to see if that restores power to the furnace blower motor. If there is still no power, check for a blown fuse in the furnace control panel.
If there is power to the black wires, set the multimeter to Ohms and touch one probe of the meter to each terminal on

how to test a motor

A furnace blower motor is one of the most important parts of your furnace. The motor is responsible for circulating air throughout the furnace and into your home. If the motor fails, the furnace will not be able to circulate air, and your home will not be heated properly.

You can test a furnace blower motor with a multimeter to see if it is working properly. First, turn off the power to the furnace. Then, remove the access panel from the furnace so that you can access the blower motor.

Next, use the multimeter to test for continuity between the two terminals on the motor. If there is continuity, then the motor is likely working properly. However, if there is no continuity, then the motor may need to be replaced.

how to test a multimeter

If you’re troubleshooting a furnace blower motor, you can use a multimeter to test it for continuity. First, turn off the power to the furnace. Then, remove the blower motor from the furnace and disconnect the wires. Use your multimeter to test for continuity between the two wire terminals on the motor. If there is continuity, that means the motor is good and you can move on to testing other components in the furnace. If there is no continuity, that means the motor is bad and needs to be replaced.

how to test

A furnace blower motor is an important part of a furnace. The motor blows air through the furnace to heat the house. If the motor is not working, the furnace will not work. You can test the motor with a multimeter to see if it is working properly.

1. Turn off the power to the furnace.

2. Remove the access panel to the blower motor.

3. Set your multimeter to the ” Ohms” setting.

4. Touch one probe of the multimeter to each of the two terminals on the blower motor. If the reading on the multimeter is infinity, then there is no continuity and the motor is bad. If you get a reading of zero or close to zero, then there is continuity and the motor is good.

how to use a multimeter

If you’re like most people, you probably don’t think much about your furnace blower motor until it stops working. In most cases, a failing blower motor will cause your furnace to make strange noises, or it will simply stop blowing altogether. If you suspect that your furnace blower motor is failing, you can use a multimeter to test it for continuity.

First, locate the furnace blower motor. In most cases, it will be mounted on the side of the furnace near the bottom. Once you’ve located the motor, remove the access panel so that you can get to the wiring.

Next, use your multimeter to test each of the wires leading to the furnace blower motor. Set your multimeter to the “ohm” setting, and touch one lead to each of the wires. If there is continuity between the two wires, the multimeter will beep or register a reading on the screen. If there is no continuity, that means that there is a break in one of the wires and the motor will need to be replaced.

Previous

how to test a magneto coil with a multimeter

how to test a generator with a multimeter

Next

Leave a Comment