how to make tri wing screwdriver

| |

If you’re like me, you’ve probably looked at a tri wing screw and thought to yourself, “how on earth do I even begin to unscrew that?” Well, never fear! With this handy guide, you’ll have that tri wing screw out in no time.

Introduction

Hello, in this instructable I will be showing you how to make a Tri-Wing Screwdriver.

This is my first Instructable so please excuse me if it isn’t very good.

I made this because I needed a Tri-Wing Screwdriver to take apart my Nintendo DS Lite, but I didn’t want to spend the money on one because I would only need it once.

This screwdriver is very easy and quick to make and only requires a few materials that you probably already have lying around the house.

What is a tri wing screwdriver?

A tri wing screwdriver is a type of screwdriver that is commonly used in electronics repair. It is named for its three-pronged head, which allows it to fit into the triangular-shaped screws often used in electronics. These screwdrivers are also sometimes called Y-shaped screwdrivers or cross head screws.

How to use a tri wing screwdriver?

There are many uses for a tri wing screwdriver, but the most common is to open up electronic devices such as game consoles, laptops, and cell phones. These screws are also known as tri-point screws and are used in many devices because they are more tamper-resistant than traditional Phillips or flathead screws.

If you need to use a tri wing screwdriver, start by finding the right size for the screws you need to remove. Once you have the right size, insert the tip of the driver into one of the slots on the screw head and turn it counterclockwise to loosen the screw. Repeat this process for all of the screws you need to remove. Once all of the screws are loose, you can carefully take apart your device.

Tips for using a tri wing screwdriver

There are a few things to keep in mind when using a tri wing screwdriver to avoid stripping the screws or causing other damage. First, make sure the screwdriver is the correct size for the screws you’re trying to remove. Second, use a light touch when applying pressure to the screwdriver – too much force can strip the head of the screw. Finally, be careful not to slip and damage the surface around the screw. With these tips in mind, you should be able to remove screws with a tri wing screwdriver without any problems.

How to care for a tri wing screwdriver

If you use a tri wing screwdriver, it is important to take care of it so that it lasts for a long time. Here are some tips on how to care for your tri wing screwdriver:

-Store the screwdriver in a dry place when not in use.
-Do not leave the screwdriver exposed to direct sunlight or heat for extended periods of time.
-If the screwdriver gets wet, dry it off immediately with a clean cloth.
-Do not use the screwdriver to pry open objects or apply excessive force.
-Regularly inspect the screwdriver for signs of wear and tear, and replace any damaged parts.

FAQs about tri wing screwdrivers

Q: Do I need a separate tri wing screwdriver for each game console?
A: No. You can use the same tri wing screwdriver for all game consoles.

Q: How do I know if a tri wing screwdriver is compatible with my game console?
A: All tri wing screwdrivers are compatible with all game consoles.

Q: What is the difference between a tri wing screwdriver and a regular Phillips head screwdriver?
A: A regular Phillips head screwdriver has two wings, while a tri wing screwdriver has three wings. The three wings on the tri wing screwdriver allow for greater torque, making it easier to remove screws that are stuck or tight.

Conclusion

Assuming you have all the tools you need, making a tri wing screwdriver is actually quite simple. Just follow the steps outlined above and you’ll have your own screwdriver in no time.

Further reading

-http://www.wikihow.com/Make-a-Tri-Wing-Screwdriver
-https://www.instructables.com/id/How-to-make-a-Triwing-screwdriver/

Previous

how to open a ds without a tri wing screwdriver

how to open a door with a flathead screwdriver Have you ever been in a situation where you need to open a door, but all you have is a flathead screwdriver? Well, have no fear! With this easy-to-follow guide, you’ll be opening doors with flathead screwdrivers in no time.Introduction

Next

Leave a Comment